CH701 Series Shark Cyclone™ PET Handheld Vacuum - FAQs

CH700WM: Meet the new Shark Cyclone™ Handvac. Its HyperVelocity suction provides compact power with the convenience of a handvac. The Shark Cyclone™ is only 1.6lbs and has USB charging to make on-the-go cleaning, a reality. The handvac is compact however,  provides XL dust cup capacity to guarantee an extended cleaning session when needed.

CH701/CH701C: Meet the new Shark Cyclone™ PET Handvac. Its HyperVelocity suction provides compact power with the convenience of a handvac. The Shark Cyclone™ is only 1.6lbs and has USB charging to make on-the-go cleaning, a reality. The handvac is compact however, provides XL dust cup capacity to guarantee an extended cleaning session when needed. The new PetExtract™ Hair Tool accessory uses rubber fins to pull in stubborn pet hair on sofas, carpets, and more. 

All accessories attach directly to the vacuum nozzle.

To remove an accessory, slide it straight off the nozzle.

To use your NEW PetExtract accessory tool, first slide the accessory onto the nozzle. 

When you are ready to begin using the tool, slide the power switch to the “I” position to power on. The best way to use this tool is to push and pull the unit in a rapid back and forth motion on the desired area of hair pick up. The felt and flaps help to pick up the pet hair while simultaneously self-cleaning the brush roll to suck it all into the dust cup! 

You can use this on many surfaces throughout your home: you couch, bed, carpet and much more! 

The dust cup should be removed to empty debris that was picked up, clear clogs in the inlet, to rinse out the dust cup to clean it, or to remove and rinse the filter (with water only.)

• First, slide the switch into the "O" position to power off.
• Press the dust cup release button on the back of the hand vac and pull off the dust cup.
• Remove the filter from the dust cup by pulling the tab and then empty the debris into the trash.
• Rinse the filter with water only, and allow it to air-dry completely for up to 24 hours.
• Rinse out the dust cup with water only, and allow it to air-dry completely for up to 24 hours.
• After the filter is completely dry, reinsert it back into the dust cup and reinstall the dust cup.

Slide the power switch to the "I" position to power on. Run the nozzle over the surface to be cleaned.

Your vacuum can be used on all dry surfaces to clean up dry debris of all sizes.

Acceptable cleaning environments include: home, office, car, etc.

The average runtime is around 10 minutes.

While in use:

• Steady illuminated light - Normal operation
• Pulsing Light - Battery is low on charge

While Charging:

• Pulsing Light - Battery is charing
• No Light - Battery is fully charged. This takes approximately 6 hours for a full charge.

For optimal performance, the dust cup should be emptied each time you vacuum or when it appears full.

Filters may need to be cleaned if the vacuum is not picking up dirt, if airflow is restricted, or if you notice lighter or no suction. To maintain optimal performance, periodically tap the filter clean. Every 3 months, rinse the filter with water only. Allow it air-dry completely for at least 24 hours before reinstalling.

The dust cup should be removed to empty debris that was picked up, clear clogs in the inlet, to rinse out the dust cup to clean it, or to remove and rinse the filter (with water only.)

• First, slide the switch into the "O" position to power off.
• Press the dust cup release button on the back of the hand vac and pull off the dust cup.
• Remove the filter from the dust cup by pulling the tab and then empty the debris into the trash.

Make sure to switch the unit into the "O" position to power off before charging. Plug the USB-C end of the charging cord into the port on the handle. Plug the USB end of the charging cord into a compatible USB outlet cube or adapter (not inlcuded) and plug into a wall outlet. 

0.5L

3 Feet

2.5lbs

16.34" (L) * 3.5" (W) * 4.33"(H)

 7.2 Volts

65 Watts

8 Amps