This article contains the LA400 / NP319 Series Shark® Lift-Around® Portable Vacuum FAQs. this supports the following SKUs: LA400, LA455, NP319, NP320C, NP320W and NP320.
1. Slide vacuum pod onto floor nozzle post.
2. Insert wand into vacuum pod.
3. Insert handle into wand.
Attach hose to back of pad.
This Shark® vacuum has two powerful settings for cleaning. To clean bare floors or with accessories:
* Press the power/surface selector switch to setting (I) Hard Floor.
* To activate the brushrolls, step on the floor nozzle and tilt the handle back.
Note that the brushroll will spin slower in this mode.
Note: Use setting I for easier maneuverability on area rugs.
To clean carpets:
* Press the power/surface selector switch to setting (II) Carpet.
* To activate the brushrolls, step on the floor nozzle and tilt the handle back.
Note that the brushroll will spin faster in this mode.
Note: Move the suction control slider on the handle to MIN to reduce suction when vacuuming carpets. Slide to MAX for more suction on bare floors.
The suction control slider on the handle allows you to adjust the suction for different floor types.
Ensure the power/surface switch is set to the correct floor type before adjusting suction power.
MIN: to reduce suction and increase maneuverability on carpets.
MAX: to increase suction on hard floors.
Press the power/surface selector switch to setting (O) Off.
*For Lift-Away® Mode: Step on the pedal on the floor nozzle to lift off the pod. When finished cleaning in Lift-Away mode, reattach the pod by sliding it onto the floor nozzle post until it clicks into place.
*For above-floor cleaning with the handle only: Press the Handle Release button and pull up on the handle to detach it from the wand.
*For above-floor cleaning with the wand: Press the Wand Release button and pull up on the wand to detach it from the pod.
Filters may need to be cleaned if your vacuum stops picking up dirt, if airflow is restricted, or if you notice lighter or no suction. Between cleanings, hold filters over the trash and tap lightly to remove dust and debris as needed.
Pre-motor foam and felt filters:
* Rinse the pre-motor filters every 3 months.
* Remove the dust cup, then take out the filters.
* Rinse filters with water only, and allow them to air-dry completely before reinstalling.
* Return the filters to their housing, reinstalling the felt filter first, followed by the foam filter. * Reattach the dust cup.
Post-motor HEPA filter:
* Rinse the HEPA filter every 12 months, or as needed.
* To remove the HEPA filter, first pull the tab on the bottom of the filter door, then lift off the door.
* Press the tab on the left side of the HEPA filter and pull out the filter.
* To reinstall the HEPA filter, insert the right side of the filter first. Push in the tab on the left side of the HEPA filter until it clicks into place.
* To reinstall the door, align the top first, then press in the bottom until it clicks into place.
For optimal performance, empty the dust cup each time you vacuum, or when debris reaches the MAX FILL line.
* To remove the dust cup, pull up on the release button located on the side of dust cup handle. Tilt dust cup forward, then lift to remove.
* Hold the dust cup over the trash and press the release button. The bottom lid will drop open.
* Tap gently to empty contents.
* Press the lid shut again until it clicks.
* Tap gently to remove contents and wipe the interior of the dust cup with a soft cloth.
*To remove collected debris from lint screen, lift the tab at the top of the dust cup to open the lid. Remove debris from lint screen to clean.
* Check to make sure your vacuum is plugged in properly.
* Check circuit breaker and fuse.
* Ensure your vacuum is powered on. To reset the motor thermostat:
* Turn off and unplug your vacuum.
* Clear any blockages from the nozzle, hoses, and airways.
Empty the dust cup and clean the filters.
Allow the vacuum to cool for a minimum of 60 minutes.
Plug in your vacuum and turn on the power.
Certain dry conditions in winter or dry desert areas may cause common static electricity to build up in the vacuum, producing small shocks, similar to what you might experience from contact with doorknobs, wool sweaters, or blankets. This is harmless. In order to avoid this, we recommend moisturizing your hands and/or removing wool socks or sweaters prior to vacuuming.
* To minimize the risk of power cord damage, DO NOT run your vacuum over the power cord. If this occurs, immediately shut off power to the vacuum and remove the cord from the brushrolls or nozzle.
* Inspect the power cord and plug for any damage before use. DO NOT use your vacuum cleaner with a damaged cord or plug. Turn off power before plugging in or unplugging your vacuum cleaner. Store your vacuum cleaner with the power cord secured around the two cord hooks.
1. Turn off and unplug your vacuum.
2. Remove the dust cup. Holding it over a trash receptacle, press the release button on the dust cup. The bottom lid will drop to let dust and debris fall into the trash.
3. Open the top lid on the dust cup by lifting the tab at the top of the dust cup. Clear away any debris from the cone- shaped screen inside the dust cup, then close the lid.
4. Remove the pre-motor filters from under the dust cup. Tap filters clean over the trash to remove any excess dirt and other particles.
5. Reattach the dust cup without the filters.
6. Plug in your vacuum and turn on the power. Check for suction at the handle.
7. Remove the dust cup and reinstall the felt filter first, followed by the foam filter. Reattach the dust cup.
8. Detach the handle from the wand and the hose from the back of your vacuum.
9. Hold the handle with the opening facing up. Drop a coin into the inlet. If the coin doesn't fall through the hose, then there is a clog that must be cleared.
10. Clear any clogs, then reattach the handle and hose.
11. Plug in your vacuum and turn on the power. Check for suction at the end of the handle.
12. To access the nozzle hose, turn the nozzle over. Open the locks on the bottom of the floor nozzle by using a coin to turn them counterclockwise.
13. Lift up the nozzle hose cover.
14. Clear away any clogs or debris around the brushrolls and in the nozzle openings.
15. Once all clogs have been cleared, close the nozzle hose cover and use a coin to turn the locks clockwise to close them.
16. Reconnect the floor nozzle to the wand and pod.
17. Plug in your vacuum and turn on the power. Test for suction. If problem persists, please contact Customer Care at 1-877-581-7375.